Upcoming Toradex Easy Installer Q2 2024 Quarterly Release. |
TEI-1199 | Feature Request | Prevent Losing Configuration Block Image Installation | Apalis iMX6, Apalis iMX8, Colibri iMX6, Colibri iMX6ULL, Colibri iMX7, Colibri iMX8X, Verdin AM62, Verdin iMX8M Mini, Verdin iMX8M Plus | ConfigBlock | | No |
Description: The configuration block can be accidentally lost during the boot partition programming if the board is reset or powered off in the meantime. This change will minimize the chances of the issue happening by rewriting the config block as soon as possible after the partition is erased (<2 seconds). |
TEI-1197 | Known Issue | Unable To Install WinCE Image | Apalis iMX6, Colibri iMX6, Colibri iMX7 | | Low | No |
Description: WinCE image installation fails with error `Finished with exit code: 1 Error: "Error creating partition table"`. Workaround: Use Easy Installer 5.7.6 to install WinCE images |
TEI-1167 | Known Issue | Installation Failure With "Timeout waiting for partition" error | Apalis iMX6, Apalis iMX8, Colibri iMX6, Colibri iMX6ULL, Colibri iMX7, Verdin AM62, Verdin iMX8M Mini, Verdin iMX8M Plus | | Low | No |
Description: Image installation fails with gpt partition table and more than two partitions |
Toradex Easy Installer Q1 2024 Quarterly Release. |
TEI-1178 | Known Issue | Error Installing Image ("Too few blocks for viable filesystem") | Apalis iMX6, Apalis iMX8, Colibri iMX6, Colibri iMX6ULL, Colibri iMX7, Colibri iMX8X, Verdin AM62, Verdin iMX8M Mini, Verdin iMX8M Plus | | Low | No |
Description: Image installation might fail with the "Too few blocks for viable filesystem" error on eMMC based SoMs. |
TEI-1173 | Feature Request | Add support for ExFAT on TEZI images | Apalis iMX6, Apalis iMX8, Colibri iMX6, Colibri iMX6ULL, Colibri iMX7, Colibri iMX8X, Verdin AM62, Verdin iMX8M Mini, Verdin iMX8M Plus | Buildsystem | | No |
Description: Add support for ExFAT filesystem. |
Upcoming Toradex Easy Installer Q4 2023 Quarterly Release. |
TEI-1109 | Known Issue | Tezi GUI Is Very Slow | Verdin AM62 | | Low | No |
Description: Tezi is very slow, to the point that installation could actually fail with timeout on low-end module variants Workaround: Disconnect any HDMI monitor and use VNC. |
Upcoming Toradex Easy Installer Q2 2023 Quarterly Release. |
TEI-1094 | Known Issue | Unable To Start When DSI Bridge Is Not Present (0071, 0072 SKUs) | Verdin AM62 | | Low | No |
Description: The Toradex Easy Installer is not working on Verdin AM62 boards without the DPI-DSI bridge (0071 and 0072 PID4). |
Upcoming Toradex Easy Installer Q2 2023 Quarterly Release. |
TEI-1048 | Feature Request | Add poweroff command | Apalis iMX6, Apalis iMX8, Colibri iMX6, Colibri iMX6ULL, Colibri iMX7, Colibri iMX8X, Verdin AM62, Verdin iMX8M Mini, Verdin iMX8M Plus | | | No |
Description: This adds the halt and poweroff commands to the TEZI rootfs.
Due to the simple init used the tools need to bypass init and directly direct call the kernel systemcalls. I.e. they need to be called with the `-f` parameter. |
Upcoming Toradex Easy Installer 5.7.7 Maintenance Release |
TEI-1167 | Known Issue | Installation Failure With "Timeout waiting for partition" error | Apalis iMX6, Apalis iMX8, Colibri iMX6, Colibri iMX6ULL, Colibri iMX7, Verdin AM62, Verdin iMX8M Mini, Verdin iMX8M Plus | | Low | No |
Description: Image installation fails with gpt partition table and more than two partitions |
Upcoming Toradex Easy Installer 5.7.6 Maintenance Release |
TEI-1178 | Known Issue | Error Installing Image ("Too few blocks for viable filesystem") | Apalis iMX6, Apalis iMX8, Colibri iMX6, Colibri iMX6ULL, Colibri iMX7, Colibri iMX8X, Verdin AM62, Verdin iMX8M Mini, Verdin iMX8M Plus | | Low | No |
Description: Image installation might fail with the "Too few blocks for viable filesystem" error on eMMC based SoMs. |
Upcoming Toradex Easy Installer 5.7 Maintenance Release 2 |
TEI-1045 | Known Issue | NAND Bad Block Table Is Corrupted At Every Boot | Colibri iMX7, Colibri T20, Colibri VF50, Colibri VF61 | Flash, Kernel | Low | No |
Description: The NAND bad block table is getting corrupted at every boot because of a configuration mismatch between U-Boot (using OOB data for bad blocks) and Linux (using an in-band table at the end in the last 2 NAND blocks). This could potentially cause data loss in case a bad block is reused and the error is not recoverable with ECC. Workaround: Set `CONFIG_SYS_NAND_USE_FLASH_BBT=y` in U-Boot configuration. |
Upcoming Toradex Easy Installer Q2 2022 Quarterly Release. |
TEI-1018 | Feature Request | Implement config block generation for assembly version #id | Verdin iMX8M Plus, Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX6ULL, Colibri iMX7, Colibri iMX6, Apalis iMX8, Apalis iMX6 | ConfigBlock | Low | No |
Description: Support for PID8 naming scheme when assembly version >25 (config block generation) |
TEI-1017 | Feature Request | Implement parsing of assembly version > 25 | Verdin iMX8M Plus, Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX6ULL, Colibri iMX7, Colibri iMX6, Apalis iMX8, Apalis iMX6 | ConfigBlock | Low | No |
Description: Support for PID8 naming scheme when assembly version >25 (parsing) |
TEI-1016 | Known Issue | tezictl image-install does not show Installation started | Verdin iMX8M Plus, Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX6ULL, Colibri iMX7, Colibri iMX6, Apalis iMX8, Apalis iMX6 | | Low | No |
Description: Issues with `tezictl` when no images are available on the current feed |
TEI-1006 | Feature Request | Use text "I Accept" instead of "I Agree" | Verdin iMX8M Plus, Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX6ULL, Colibri iMX7, Colibri iMX6, Apalis iMX8, Apalis iMX6 | | Low | No |
Description: Change EULA dialog acceptance button label to "I Accept" |
Upcoming Toradex Easy Installer Q1 2022 Quarterly Release. |
TEI-992 | Known Issue | Colibri iMX7D 1GB (eMMC) V.1.1B Detection May Not Work | Colibri iMX7 | | Low | No |
Description: Detection of the Colibri iMX7D 1GB eMMC (0039) V.1.1B is not working correctly, because of that the wrong device tree is selected and Tezi is not able to read the config block. |
TEI-986 | Feature Request | tezictl: add status command and timeout | Not applicable | | Low | No |
Description: Improve tezictl timeout handling ans status reporting |
TEI-979 | Known Issue | Config block writing with TEZI and varying boot partition sizes | Verdin iMX8M Plus, Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX6ULL, Colibri iMX7, Colibri iMX6, Apalis iMX8, Apalis iMX6, Apalis TK1 | | Low | No |
Description: Replacement of eMMC chips with different manufacturers can sometimes change some parameters like the boot partition size. When using Toradex Easy Installer to write configuration blocks (raw images) it is not possible to select a negative offset to count from the end of the partition, making image.json files incompatible between old and new eMMC chips. Workaround: Use a wrapup.sh script to calculate the size of the boot partition and write the configuration block there. Tezi 5.6.0 will introduce a new offset parameter for this use case. |
TEI-968 | Feature Request | Improve the UX on grayed-out images that require a newer version of Easy Installer | Verdin iMX8M Plus, Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX6ULL, Colibri iMX7, Colibri iMX6, Apalis iMX8, Apalis iMX6 | | Low | No |
Description: Improve message in case an image requires an updated version of Toradex Easy Installer |
Upcoming Toradex Easy Installer Q4 2021 Quarterly Release. |
TEI-964 | Known Issue | Autoinstall Flag Causes Tezi to Go Into an Installation-Loop | Verdin iMX8M Plus, Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis iMX8 | | Low | No |
Description: Toradex Easy Installer is falling into a "installation-loop" if autoinstall in image.json is set to true. The Easy Installer is supposed to only auto-install newer Easy Installer versions. |
TEI-963 | Known Issue | u-boot-initial-env Not Written on NAND modules | Colibri iMX7, Colibri iMX6ULL | Bootloader | Low | No |
Description: Toradex Easy Installer does not write u-boot-initial-env on NAND modules, instead U-Boot starts with default environment after the installation. |
TEI-919 | Known Issue | Analogue VGA Not Working Out-Of-The-Box | Apalis iMX6 | Buildsystem, Graphics, VGA | Low | No |
Description: All 3 display interfaces DVI-D aka HDMI, parallel RGB as well as VGA should be brought up concurrently just like the Toradex Easy Installer 1.8 used to do. But currently, only the former two are brought up while analogue VGA requires manual intervention. Workaround: To bring up analogue VGA as well you may manually add the following device tree overlay to the overlay.txt file:
apalis-imx6_vga_overlay.dtbo |
Toradex Easy Installer Q3 2021 Quarterly Release. Learn more on https://www.toradex.com/news/540-release-of-toradex-easy-installer-for-imx-and-tk1-system-on-modules |
TEI-949 | Feature Request | Easy Installed is failed to start on module with missing config block | Apalis iMX8 | Bootloader | Low | No |
Description: Toradex Easy Installer fails to start if configuration block is missing |
TEI-921 | Feature Request | Add support for Colibri iMX6ULL 1GB | Colibri iMX6ULL | Toradex Feature | Low | No |
Description: Add support for the new eMMC and 1GB RAM variant of Colibri iMX6ULL to the same colibri-imx6ull Easy Installer machine. |
TEI-889 | Feature Request | Support Second Ethernet Interface | Verdin iMX8M Plus | Ethernet | Low | No |
Description: Support the second Ethernet interface of Verdin iMX8M Plus, with the PHY located on the carrier board. It is exposed through the connector X35, for Ethernet_2, from the Verdin Development Board. |
Toradex Easy Installer Q2 2021 Quarterly Release. Learn more on https://www.toradex.com/news/530-release-of-toradex-easy-installer-for-imx-and-tk1-system-on-modules |
TEI-791 | Feature Request | Prevent Toradex Easy Installer From Being Booted by BSP U-Boot | Verdin iMX8M Plus, Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis iMX8 | Bootloader | Low | No |
Description: An already installed BSP U-Boot should not be able to boot an Easy Installer image that is plugged into e.g. an SD-Card slot. Workaround: TBD |
TEI-181 | Known Issue | Missing Security Label Support on Ext4 | Colibri iMX8X, Apalis iMX8 | Flash | Low | No |
Description: Security labels do not get written to the target file system if they are in place in a tar file. |
TEI-173 | Known Issue | Resolution not correct when HDMI is not plugged-in | Apalis iMX8 | HDMI | Low | No |
Description: Resolution of the Toradex Easy Installer HDMI is not plugged-in is not 640x480, this leads to Remote Desktop not showing the complete Toradex Easy Installer. Workaround: Set 1024x768 as resolution manually in the Remote Desktop settings. |
TEI-649 | Feature Request | Ancient Wrong Default U-Boot Environment Leaking Into Freshly Installed Images | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Apalis iMX8 | Toradex Feature | Critical | No |
Description: Unfortunately, ancient wrong default U-Boot environment compiled into the fw-utils aka fw_printenv/fw_setenv is leaking into freshly installed images of all i.MX 8 series based modules which may have various disastrous effects leading up to and including complete boot hangs. |
TEI-632 | Feature Request | Add Support for Apalis iMX8QXP 2GB WB IT V1.1B | Apalis iMX8X | | Low | No |
Description: Add support for Apalis iMX8QXP 2GB WB IT V1.1B. |
TEI-630 | Feature Request | Add Support for Apalis iMX8QXP 2GB ECC IT V1.1B | Apalis iMX8X | | Low | No |
Description: Add support for Apalis iMX8QXP 2GB ECC IT V1.1B. |
TEI-626 | Known Issue | Analogue VGA Not Working | Apalis iMX6 | VGA | Low | No |
Description: The analogue VGA display output is not working on Apalis iMX6. Workaround: Until this feature is fixed in version 2.x please use stable version 1.8. |
TEI-610 | Feature Request | Add Support for Apalis iMX8QP 2GB WB V1.1B | Apalis iMX8 | | Low | No |
Description: Add support for Apalis iMX8QP 2GB WB V1.1B. |
TEI-609 | Feature Request | Add Support for Apalis iMX8QP 2GB V1.1B | Apalis iMX8 | | Low | No |
Description: Add support for Apalis iMX8QP 2GB V1.1B. |
TEI-606 | Feature Request | Add Support for Colibri iMX8QXP 2GB WB IT V1.0D | Colibri iMX8X | | Low | No |
Description: Add support for Colibri iMX8QXP 2GB WB IT V1.0D. |
TEI-605 | Feature Request | Add Support for Colibri iMX8QXP 2GB IT V1.0D | Colibri iMX8X | | Low | No |
Description: Add support for Colibri iMX8QXP 2GB IT V1.0D. |
TEI-604 | Feature Request | Add Support for Colibri iMX8DX 1GB WB V1.0D | Colibri iMX8X | | Low | No |
Description: Add support for Colibri iMX8DX 1GB WB V1.0D. |
TEI-603 | Feature Request | Add Support for Colibri iMX8DX 1GB V1.0D | Colibri iMX8X | | Low | No |
Description: Add support for Colibri iMX8DX 1GB V1.0D. |
TEI-602 | Feature Request | Add Support for Apalis iMX8QM 4GB IT V1.1B | Apalis iMX8 | | Low | No |
Description: Add support for Apalis iMX8QM 4GB IT V1.1B. |
TEI-596 | Feature Request | Add Support for Verdin iMX8M Mini Quad 2GB WB IT V1.1A | Verdin iMX8M Mini | | Low | No |
Description: Add support for Verdin iMX8M Mini Quad 2GB WB IT V1.1A. |
TEI-593 | Feature Request | Add Support for Verdin iMX8M Mini DualLite 1GB V1.1A | Verdin iMX8M Mini | | Low | No |
Description: Add support for Verdin iMX8M Mini DualLite 1GB V1.1A. |
TEI-592 | Feature Request | Add Support for Verdin iMX8M Mini DualLite 1GB WB IT V1.1A | Verdin iMX8M Mini | | Low | No |
Description: Add support for Verdin iMX8M Mini DualLite 1GB WB IT V1.1A. |
TEI-572 | Feature Request | Apalis iMX8QM 4GB WB RAM Issues | Apalis iMX8 | RAM, SCFW | Low | No |
Description: Some modules may show various kinds of RAM issues (U-Boot failing to boot fit images due to bad hash, random squashfs errors, random kernel panics when BSP is flashed). Closer analysis identified NXP meanwhile having updated the RAM configuration/initialisation side of things. Updating to NXP's latest Register Programming Aid (RPA) v19 seems to fix those issues. Full validation & verification pending... Workaround: Until this fix is officially released please use a recent nightly build. Note: You are looking for something like apalis-imx8/tezi/tezi-run/oedeploy/Apalis-iMX8_ToradexEasyInstaller_2.0b6-nightly-<date>.zip. https://artifacts.toradex.com:443/artifactory/tezi-oe-prerelease-frankfurt/thud/nightly/ |
TEI-563 | Feature Request | Add Support for Apalis iMX8X V1.1B and Colibri iMX8X V1.0C with i.MX8QXP C0 and PF8X00 C1 | Apalis iMX8X, Colibri iMX8X | Bootloader, CPU, Power Management | Low | No |
Description: Add Support for Apalis iMX8X V1.1B and Colibri iMX8X V1.0C with i.MX8QXP C0 and PF8X00 C1 requiring up-to-date SCFW and different SECO firmware. |
TEI-558 | Known Issue | RNDIS Networking Not Functional on Colibri iMX6ULL | Apalis iMX8X, Colibri iMX6ULL | USB | Low | No |
Description: RNDIS networking is not functional on Colibri iMX6ULL |
TEI-538 | Feature Request | Optimise Feed Loading Based on Machine or Product ID | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | | No |
Description: Optimise feed loading based on machine or product ID. |
TEI-133 | Fixed | Colibri iMX7S NAND Not Working in 2.0b4 | Colibri iMX7 | Flash | Low | No |
Description: NAND is not working on Colibri iMX7S in 2.0b4 release. Workaround: Use stable Tezi release 1.8. |
TEI-101 | New Feature | Announce VNC via zeroconf | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Ethernet | Low | No |
Description: Announce VNC capability via zeroconf. |
TEI-1028 | Known Issue | Duplicate Images in Feed | Not applicable | | Low | No |
Description: Images in the Feed list may be shown more than once. Workaround: Restart Easy Installer or delete the contents in /var/volatile/ from a console and press refresh. |
TEI-1002 | Known Issue | Random MAC Address When Launched Via USB Recovery Mode | Verdin iMX8M Plus | | Low | No |
Description: Random MAC address leading to ever changing IP address when launched via USB recovery mode even though ConfigBlock is intact. |
TEI-991 | Known Issue | Colibri iMX7D 1GB (eMMC) V1.1B Not Working With Version 1.8 | Colibri iMX7 | | Low | No |
Description: The Toradex Easy Installer 1.8, when flashed to the eMMC of a 0039 Colibri iMX7D 1GB (eMMC) V1.1B, is not working correctly as the ConfigBlock is not properly read. Workaround: `setenv variant -emmc` in U-Boot before booting (it's not possible to save the variable change). |
TEI-920 | Feature Request | No ConfigBlock Plausibility Checks Done | Verdin iMX8M Plus, Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis iMX8 | ConfigBlock, Toradex Feature | Low | No |
Description: After flashing a Verdin iMX8M Plus ConfigBlock into an Apalis iMX6 the Toradex Easy Installer displays such without doing any further checks. It could easily detect this inconsistency and display the same dialog as if the ConfigBlock could not be read. |
TEI-740 | Known Issue | Reports Bogus/Confusing Version Information (TDX_VER_ID) | Verdin iMX8M Plus, Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Buildsystem, Toradex Feature | Low | No |
Description: On the serial console the Toradex Easy Installer reports bogus/confusing version information:
TDX_VER_ID="Colibri-iMX7_ToradexEasyInstaller_2.0b7-nightly-20201104"
Instead of Colibri-iMX7_ToradexEasyInstaller_2.0b7-nightly-20210323 which is what I am running! |
TEI-574 | Feature Request | Add the commands poweroff and shutdown | Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX6ULL, Colibri iMX7, Colibri iMX6, Apalis iMX8, Apalis iMX6, Apalis TK1, Apalis T30 | | Low | No |
Description: Add the commands poweroff and shutdown |
TEI-550 | Known Issue | Installer doesn't start automatically on Apalis TK1 | Apalis TK1 | Toradex Feature | Low | No |
Description: Installer doesn't start automatically on Apalis TK1 |
TEI-484 | Feature Request | Random MAC Address Leading to Random Ethernet IP Address | Colibri iMX7 | | | No |
Description: In recovery mode U-Boot cannot read the config block which leads to assign a random MAC address. |
TEI-483 | Known Issue | Erase Flash (c) Does Not Preserve Raw NAND Flash Erase Counters | Colibri iMX7, Colibri iMX6ULL | | | No |
Description: The "Erase Flash (c)" button on the Easy Installer does not preserve the NAND flash erase counters in /sys/class/ubi/ubi0/max_ec. |
TEI-340 | Feature Request | Support DNS-SD Service Discovery | Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1 | Ethernet | Low | No |
Description: Toradex Easy Installer should support using DNS-SD to discover an appropriate image server. Workaround: Use server discovery using zeroconf technologies or use a custom local DNS Server which resolves tezi.toradex.com to a local image server. |
TEI-312 | Feature Request | Add support for optional files (not writing everything from scratch) | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Support optional flashing artifacts using a property in the image descriptor. |
TEI-309 | Feature Request | Add feature to hide/show unsupported images | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Add a check box which allows to also show images which are not compatible with the currently used hardware. By default the check-box is not selected and only compatible images are shown. |
TEI-282 | Known Issue | Only 256MB of RAM Available When Installing BSP V2.6 Directly From Toradex Easy Installer U-Boot Due to Missing patch_ddr_size Command | Colibri iMX6 | Bootloader | Low | No |
Description: During installation of BSP V2.6 directly from the Toradex Easy Installer U-Boot the following error message is shown but otherwise ignored by the installation procedure:
Unknown command 'patch_ddr_size' - try 'help'
As a consequence only 256MB of RAM will be available. Workaround: Just manually execute the patch_ddr_size command once U-Boot from BSP V2.6 is installed.
For existing production programming scenarios we do recommend to first separately update just U-Boot only (e.g. doing run setupdate; run update_uboot; reset) in order to make sure any further production programming scripting will proceed as before. |
TEI-276 | Feature Request | Provide a mechanism to write at a specific offset from the end of the eMMC partition | Colibri iMX7, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Flash | Low | No |
Description: Provide a mechanism for raw files which allows to write at a specific offset from the end of the partition. This is useful to handle WinCE Config Block which is located at the end of the eMMC boot partition. Because eMMC boot partition sizes can vary the offset from the beginning depends on the exact product and product version. Workaround: Use the wrapup.sh script to dd the configblock (or any other file) with a calculated offset from the end of the partition. For example:
...
IMAGE_FOLDER=$4
...
OFFSET=$(($(cat /sys/block/mmcblk0boot0/size)-17))
echo "Writing configblock.bin to offset ${OFFSET}"
dd if=${IMAGE_FOLDER}/configblock.bin of=/dev/mmcblk0boot0 count=16 seek=$OFFSET
This also makes sure that the static config block does not get accidentally overwritten in case configblock.bin is too long.
Note that this only works for images read from a local media, since only then configblock.bin is simply available in $IMAGE_FOLDER. |
TEI-274 | Feature Request | Support flashing WinCE splash screen | Colibri iMX7 | WinCE Feature | Low | No |
Description: Support flashing WinCE splash screen. |
TEI-253 | Known Issue | Consider Including U-boot Environment Partition | Colibri iMX7, Apalis iMX6, Colibri iMX6 | Bootloader | Low | No |
Description: The default U-boot shipped on modules with Tezi no longer includes a U-boot environment partition on the flash. This is an issue for customers who don’t replace the U-boot that comes on the module but want to set kernel arguments (e.g. video settings). Workaround: Flash a U-boot which includes an environment partition & support for saveenv. |
TEI-249 | Feature Request | Make ext3 Message More Dynamic From JSON | Apalis iMX6, Colibri iMX6 | Flash | Low | No |
Description: There is a hard-coded ext3 message somewhere in the Qt Tezi UI. |
TEI-248 | Known Issue | Recovery May Fail on Windows 7 | Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Bootloader | Low | No |
Description: While launching the Toradex Easy Installer via recovery mode works on Windows 10 it may fail on Windows 7. |
TEI-205 | Feature Request | Support filtering by product revision | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Currently images and files inside an image can be selected to be compatible with a product ID(s) using the "supported_product_ids" property. It should be also possible to filter by product revision. |
TEI-199 | Known Issue | Toradex Easy Installer 0.5 Beta Does Not Run After Installation | Apalis iMX6 | Bootloader | Low | No |
Description: Installing tezi 0.5 beta and doing a full power-cycle fails running it. |
TEI-192 | Known Issue | iMX7: recovery-windows.bat does not find USB device if it is connected behind a (USB3?) hub | Colibri iMX7 | USB | Low | No |
Description: Recovery mode might not work if there is a USB hub between the Colibri iMX7 and the PC.
Workaround: Remove the USB hub, connect the Colibri directly to the PC. |
TEI-180 | Known Issue | Feeds loading continuous despite image installation already started or even finished | Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Colibri iMX6, Apalis TK1, Apalis iMX8 | Toradex Feature | Low | No |
Description: Loading the image list might generate errors even if the user started an image installation already (e.g. installing from a local device). This error message(s) do not disturb or interrupt the installation, but are confusing and unnecessary. Workaround: Ignore "Error downloading image list" messages during installation. |
TEI-179 | Feature Request | Refresh does not work sometimes | Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis iMX8 | Toradex Feature | Low | No |
Description: Refreshing images sometimes does not reload the image description files. Workaround: Restart the Toradex Easy Installer. Manually clear the Qt Network disk cache using "rm -rf /tmp/data8/". |
TEI-174 | Known Issue | RDP doesn't work when network changed | Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis T30, Apalis iMX8 | Ethernet | Low | No |
Description: RDP does not work when network is changed and Toradex Easy Installer gets a new IP. Workaround: Flash Toradex Easy Installer with correct network attached and do not change it on runtime. |
TEI-170 | Known Issue | Using RDP the mouse cursor updates slowly or even gets stuck | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Especially on the lower end module the user interface over RDP feels slow. The mouse cursor and UI elements updates slowly and sometimes get even stuck. |
TEI-156 | Known Issue | FreeRDP May Fail Connecting Due to Enabled Server Heartbeat PDU | Apalis iMX8 | Graphics | Low | No |
Description: FreeRDP commit 753b9c7ce9af ("Enable server heartbeat PDU by default.") changed heartbeat to be enabled by default which fails connecting to the Toradex Easy Installer running Weston RDP backend. Workaround: Start FreeRDP with heartbeat being disabled e.g. as follows
xfreerdp -heartbeat -v:192.168.11.1 |
TEI-150 | Known Issue | Restoring config block broken on raw NAND | Colibri iMX7, Colibri iMX6ULL | ConfigBlock | Low | No |
Description: Restoring config block on Toradex Easy Installer 2.0b1 on module with raw NAND is not functional. |
TEI-129 | Feature Request | Older Modules May Fail Booting Due to SoC Fusing Issue | Apalis iMX6, Colibri iMX6 | Bootloader | Low | No |
Description: Attempting to install a BSP 2.6 or later on an older Apalis iMX6 V1.0A, V1.1A, V1.1B (Apalis iMX6Q 2GB IT before 2017-05-30 only) or Colibri iMX6 V1.0A module for the first time may subsequently fail booting due to SoC fusing not being possible. Workaround: Either use the legacy update procedure or an older Toradex Easy Installer version like stable 1.8. |
TEI-126 | Feature Request | Support fusing of modules using upstream Kernel | Apalis iMX6, Colibri iMX6 | | Low | No |
Description: If you attempt to install BSP 2.6 or later on an older Apalis iMX6 V1.0A, V1.1A, V1.1B (Apalis iMX6Q 2GB IT before 2017-05-30 only) or Colibri iMX6 V1.0A module for the very first time it will not work, as prior to the Easy Installer version 2.0b4 we used to fuse them directly in that application. Later modules we since fuse in production. Workaround: If you have one of the listed modules contact Toradex. |
TEI-124 | Known Issue | Un-Plugging HDMI Makes Other Display Flicker/Slow-Down and Gives Kernel Backtrace | Apalis T30 | Graphics, HDMI, RGB | Low | No |
Description: Un-plugging HDMI during runtime makes the other display flicker/slow-down and gives a kernel backtrace. Workaround: Do not un-plug HDMI during runtime. |
TEI-123 | Known Issue | Flashing Images using Windows is not working | Apalis TK1, Apalis T30 | Toradex Feature | Low | No |
Description: Flashing images using Windows is not working for Apalis T30 and Apalis TK1. |
TEI-113 | Known Issue | Extend validity time of RDP certficates | Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Colibri iMX6, Apalis TK1, Apalis iMX8 | Toradex Feature | Low | No |
Description: If the RTC does not provide a valid time and there is no internet connectivity, the Toradex Easy Installer sets the time to the build time. This time is used to generate the RDP certificate. When using the Toradex Easy Installer later than one year after the build time, the certificate will no longer be valid. The validity should be set to a reasonable long lifetime. |
TEI-103 | Known Issue | Toradex Easy Installer does not Remove U-Boot Environment Variables | Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: This is by design: Toradex Easy Installer merges the variable currently in the environment with the variables in the supplied text file.
This is taken care of on the BSP side #58122. Workaround: To delete a variable, add a variable with the same name but without a value (e.g. test=). Alternatively, erase the flash before flashing a new image to make sure only the variables in the supplied text file are set in the environment. |
TEI-99 | Feature Request | RDP does not work with Windows RDP Client | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Windows RDP client exits with an "internal error" when connecting to Tradex Easy Installer. Workaround: Use Linux RDP client. |
TEI-95 | Feature Request | Use a DHCP Option to Provide HTTP Server Address to the Images | Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1 | Ethernet | Low | No |
Description: If the Toradex Easy Installer is used with network only there is no way to provide a custom HTTP server to fetch the images from. Use a DHCP option to provide a HTTP image server. |
TEI-92 | Known Issue | Drop VNC in Favour of Using RDP | Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Graphics | Low | No |
Description: With us moving to Qt 5, we dropped VNC support in favour of using RDP. |
TEI-66 | Feature Request | Make Prepare/Wrap-Up Script Timeout Configureable | Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1 | Toradex Feature | Low | No |
Description: Normally prepare and wrap-up scripts execute only relatively short migration type tasks. Toradex Easy Installer therefor calls the scripts with a timeout of 30s. However, the scripts can be useful for various applications, such as flashing the complete image using a script itself. For this type of application a longer timeout is required. The timeout should be a configuration option in the JSON file. |
TEI-61 | Known Issue | Update lib: Invalid registry file generated on imx6 | Apalis iMX6, Colibri iMX6 | WinCE Feature | Low | No |
Description: The exported registry file for i.mx6 is not valid and re-importing it restores the default registry instead. |
TEI-59 | Known Issue | Toradex Easy Installer May Fail Bringing-Up USB | Colibri iMX7 | USB | Low | No |
Description: The Toradex Easy Installer 1.3 may fail bringing-up USB properly showing the following error on the serial debug console: usb usb1-port1: cannot reset (err = -32) Workaround: Just power-cycle and try again. Plugging the device in after boot may also help. |
TEI-49 | Feature Request | Possibility to Change Parts of Bsp (U-Boot, Kernel or Devicetree) separately | Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: - |
TEI-47 | Known Issue | Reduce the installed licenses disk usage by providing a manifest | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Currently a whole copy of the licenses is installed instead of a manifest only. |
TEI-45 | Feature Request | Support Colibri iMX8X Modules | Colibri iMX8X | Kernel | Low | No |
Description: Port Toradex Easy Installer to Colibri iMX8X modules. |
TEI-44 | Known Issue | Unmounting media from the wrapup script is not working | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Multimedia | Low | No |
Description: When using the wrapup script to write into its storage medium (e.g. for log files, etc) and issuing a reboot thereafter, the medium should be first unmounted to avoid data corruption. A suggested way to unmount the medium wherefrom the wrapup script is executed is to create a delegate script in memory and exec it from the same wrapup. This approach doesn't seem to work, as umount will complain the resource is busy. |
TEI-42 | Feature Request | Consider adding an autoreboot option in image.json | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Rebooting the system from the Easy Installer wrapup script is possible (by issuing the `reboot -f` command), but busybox will not unmount volumes on reboot, so such a reboot might lead to data corruption on an image from an SD card. |
TEI-40 | Known Issue | Error Downloading Image List Shown | Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Error downloading image list. Intermittently, shown upon boot. Alternatively, if clicking on Feeds (f) too quick while it is still loading stuff this error is also always shown. |
TEI-39 | Known Issue | CPU Frequency Scaling Error During Boot | Colibri iMX7 | CPU, Power Management | Low | No |
Description: The following is displayed in the serial debug console upon boot:
[ 17.672131] cpu cpu0: failed to scale vddarm up: -22
[ 17.677125] cpufreq: __target_index: Failed to change cpu frequency: -22 |
TEI-36 | Feature Request | Add support for Wi-Fi built-in or dongle | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Wi-Fi | Low | No |
Description: Having Wi-Fi support makes it easier for evaluation purposes. Workaround: Duplicate |
TEI-35 | Feature Request | Support product number in addition to product id | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: The image.json should provide an option to filter by full product number (8 digit) in addition to product id only (4 digit). |
TEI-20 | Known Issue | USB 3.0 Devices Plugged in at Boot Time Behind a USB Hub is not Accessible | Colibri iMX7 | USB | Low | No |
Description: On the Colibri Evaluation Board V3, a USB 3.0 device plugged in at boot time is not accessible after boot. Furthermore, the device seems to influence the on-board USB hub in a way that any USB port 1-4 won't work anymore. Workaround: Plug the USB 3.0 flash drive after startup or use a USB 2.0 flash drive. |
TEI-19 | Known Issue | USB Ports do not Work Sometimes | Apalis TK1 | USB | Low | No |
Description: USB ports at times do not work Workaround: Power cycle the device |
TEI-7 | Known Issue | Detect Existance of Boot Configuration Block | Colibri iMX7, Colibri iMX6ULL | Flash | Low | No |
Description: Currently the existence of the Toradex Config Block is used to determine whether a valid BCB (boot configuration block) is present. Technically, those are two separate things. It is possible to erase the flash and only write the Troadex Config Block from U-Boot, in which case the Toradex Easy Installer will assume that there is a valid BCB. This sequence leads to a unbootable module. |
TEI-5 | Known Issue | Allow Toradex Easy Installer Automatic Installations if Run From RAM | Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Colibri T30, Apalis T30, Apalis iMX8 | RAM | Low | No |
Description: Trying to automatically install an older or equal version of the Toradex Easy Installer from a running Toradex Easy Installer is not allowed. This is desired in most use cases (e.g. installing from an SD card), but it can become a problem in others, particularly when re-flashing the Toradex Easy Installer from a recovery image. Workaround: Currently the workaround for this is setting `isinstaller: false` in the json config, but this may cause problems of infinite install loops. |
TEI-2 | Feature Request | Use DHCP Option 12 to Communicate Hostname | Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30 | Ethernet | Low | No |
Description: Currently, the DHCP client used in Toradex Easy Installer does not provide a hostname. So even when using a DHCP server with DNS integration it will not be possible to ping the Toradex Easy Installer by hostname/FQDN. Workaround: Use server discovery using zeroconf technologies or use a custom local DNS Server which resolves tezi.toradex.com to a local image server. |
TEI-1195 | Known Issue | USB Hub on Apalis Evaluation Board Doesn't Work | Apalis iMX6, Apalis iMX8 | | Low | No |
Description: The USB hub on the carrier board is not working. This renders the USB host ports on connectors X53 and X54 unusable, except for the first port on X54 (USBH3). |
TEI-1020 | Known Issue | u-boot-fw-utils default environment is wrong | Apalis iMX6, Apalis iMX8, Colibri iMX6, Colibri iMX6ULL, Colibri iMX7, Colibri iMX8X, Verdin iMX8M Mini, Verdin iMX8M Plus | | Low | No |
Description: When the user provides an environment file as part of the image.json, and the environment partition is deleted, Tezi will install the default environment from BSP 5 and append the variables on the user provided environment file. Workaround: You can delete unwanted variables as defined by the Toradex Easy Installer specification: Add the variable without any value in the file used by u_boot_env (ie. vidargs=) |
TEI-774 | Feature Request | Add Support For filesystem_type: swap | Verdin iMX8M Plus, Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis iMX8 | | Low | No |
Description: Add support for filesystem_type: "swap", so that a swap partition can be setup during an Easy Installer installation. |
TEI-725 | Feature Request | Progress Bar Not Working for Raw Files | | | Low | No |
Description: Adding the "size" property to raw files, as described on Toradex Easy Installer: Configuration Files: Raw Files, does not make the progress bar display the installation progress. |
TEI-710 | Feature Request | Support Loading Toradex Easy Installer From USB Stick/SD Card Using Distroboot | Verdin iMX8M Plus, Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Distroboot from USB Stick/SD Card may allow you to load Toradex Easy Installer into a Toradex SoM without the need of going through recovery mode, which involves exposing a USB OTG interface and using a computer. While this seems easier, due to limitations on the SoC vendors BSP - such as the SCU firmware - it is not a maintainable feature and therefore not supported by Toradex. Workaround: Keep in mind that Toradex Easy Installer is a production programming tool, not meant to be used as an update tool. If you need to update the full OS image for devices on the field and still insist on using it, make sure that your hardware design is aware of the requirements for entering recovery mode. Alternatively, consider adopting an OTA solution: for instance, if you are using Torizon, consider adopting Torizon OTA. |
TEI-551 | Feature Request | Support custom icon name for Toradex Easy Installer images | Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Currently the Toradex Easy Installer image class on Yocto hardcodes the icon to "toradexlinux.png". A customer might want to use his own icon, named differently. Workaround: In your Yocto layer, create a file named "recipes-bsp/tezi-metadata/tezi-metadata_%.bbappend" and add a function "do_deploy_append()" where you overwrite "toradexlinux.png". |
TEI-490 | Known Issue | Add new Feed: pressing numbers selects/unselects servers (even in input field) | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Add new Feed: pressing numbers selects/unselects servers (even in input field). |
TEI-289 | Feature Request | Show a Warning if an Image is Likely Too Large | Colibri iMX7, Colibri iMX6ULL | Flash | Low | No |
Description: Since UBIFS is compressed on-the-fly the Toradex Easy Installer cannot reliably estimate whether an image fits on internal NAND ahead of time. However, Toradex Easy Installer should make a rough estimate and print a warning if the UBIFS will likely not be able to fit the image. |
TEI-278 | Feature Request | Do Not Mux Any Pins as Output Which is Not Essential for Toradex Easy Installer | Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis iMX8 | GPIO | Low | No |
Description: To allow using Toradex Easy Installer on carrier boards which use non Colibri/Apalis standard functionality the Toradex Easy Installer should make sure to not mux/use any non-essential pin. |
TEI-250 | Feature Request | No Way to Deploy Alternate Device Tree on NAND Modules | Colibri iMX7 | Device Tree | Low | No |
Description: While we deploy all device tree blobs into the FAT partition of our eMMC modules currently in the NAND case we only deploy one single one. In the previous case of using our U-Boot update scripts the one chosen was dependent on the fdt_board environment variable. Now in the Tezi case there is no way to influence this yet. |
TEI-235 | Feature Request | Add Checksum for Files Written to Flash | Colibri iMX7, Apalis iMX6, Colibri iMX6 | Flash | Low | No |
Description: To validate integrity of the image a checksum for each file getting written to the flash should be stored in the image description file. |
TEI-227 | Feature Request | Support Resistive Touch Screen | Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Resistive Touch | Low | No |
Description: Resistive touch screens cannot be calibrated yet. Workaround: Use a USB mouse to control the Toradex Easy Installer user interface. |
TEI-145 | Feature Request | Show Easy Installer on Parallel RGB and DVI/HDMI Simultaneously | Colibri iMX8X | RGB | Low | No |
Description: Due to a combination of hardware and software architecture issues it is currently not easily possible to clone the same output to HDMI and parallel RGB. |
TEI-144 | Feature Request | Use kexec to Start Toradex Easy Installer From a Running Linux System | Verdin iMX8M Mini, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Kernel | Low | No |
Description: Support running Toradex Easy Installer from within a running Linux system using kexec. |
TEI-143 | Feature Request | Move to New Versioning Scheme | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Use the new Toradex versioning scheme. |
TEI-139 | Feature Request | Announce HTTP API through AVAHI | Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Announce the Toradex Easy Installer HTTP API on the local network using AVAHI. |
TEI-132 | Feature Request | Add support for Apalis iMX8X 1.1A | Apalis iMX8X | Kernel | Low | No |
Description: Add support for Apalis iMX8X 1.1A |
TEI-131 | Known Issue | VNC Cannot be Used after Disconnecting RNDIS while having a VNC Session Running | Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: When disconnecting RNDIS while a VNC session is running, no other VNC session can be created anymore. Workaround: Restart the Toradex Easy Installer. |
TEI-116 | Feature Request | Support 10" LVDS Display | Apalis iMX6, Apalis TK1, Apalis iMX8 | LVDS | Low | No |
Description: Support Toradex Capacitive Touch Display 10.1" |
TEI-109 | Feature Request | Do Not Store File Sizes in image.json | Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Toradex Feature | Low | No |
Description: Allow to estimate size of images correctly without specifying sizes in image.json. |
TEI-107 | Feature Request | Support LVDS Screen in Toradex Easy Installer | Apalis iMX6 | Graphics, LVDS | Low | No |
Description: Support LVDS Screen in Toradex Easy Installer |
TEI-106 | Known Issue | Toradex Easy Installer doesn't boot from USB | Apalis iMX6 | USB | Low | No |
Description: Toradex Easy Installer doesn't boot from USB. |
TEI-79 | Feature Request | Avoid Downloading Unrelated image.json from Server | Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30 | Toradex Feature | Low | No |
Description: Currently the Toradex Easy Installer downloads every image.json references in a image list just to check whether the image is compatible with the module at hand. This does not scale well as we add support for more and more modules. Introduce a image list format which states which modules a particular image is for. |
TEI-46 | Feature Request | Colibri iMX7 With WinCE Does Not Boot After Flashing an Image Using Toradex Easy Installer | Colibri iMX7 | Flash | Low | No |
Description: Toradex Easy Installer sometimes can fail to update a NAND Flash Colibri iMX7. eMMC Colibri iMX7 are not affected. Workaround: Use the flashimage command in Eboot, or the UpdateTool in Windows CE to program a new image. |
TEI-33 | Known Issue | Feed server not found through RNDIS | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | USB | Low | No |
Description: When using RNDIS to download an image list from a custom server in a host, tezi silently fails. |
TEI-28 | Known Issue | Toradex Easy Installer sometimes fails to install image from Internet | Verdin iMX8M Mini, Apalis iMX8X, Colibri iMX8X, Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1, Apalis T30, Apalis iMX8 | Ethernet | Low | No |
Description: Installing from Internet sometimes gets stuck at the very beginning. |
TEI-899 | Feature Request | Assess and Generalize Recovery Mode Handling | Colibri iMX7, Colibri iMX6ULL, Apalis iMX6, Colibri iMX6, Apalis TK1 | Bootloader | Low | No |
Description: Assess and generalize recovery mode handling. Make sure upon recovery mode detection the default U-Boot environment is used rather than the one stored in flash to avoid any bad side-effects. Once U-Boot proper is running automatically start USB fastboot to allow for downloading further parts like e.g. the Toradex Easy Installer ITB. Workaround: The downstream bring-up i.MX 8/8X/8MM U-Boot already behaves like that and maybe consulted for guidance. |